Trouble with selecting a single wire segment of a net in Altium - Electrical Engineering Stack Exchange


below want select , edit bottom wire of 3 parallel wires:

enter image description here

but when click on bottom wire program selects middle wire because share same net.

is possible single out desired wire segment without selecting entire net in altium?

yes

you need use "break wire" feature first - split wire up. think it's in "edit" menu.


Comments

Post a Comment

Popular posts from this blog

Nyquist-Shannon sampling theorem on non infinite signals - Electrical Engineering Stack Exchange

Image
can sample , recover signals non infinite "length" using nyquist shannon theorem? example if have signal $$ x(t)= u(t+5)-u(t-5) $$ , know sampling period t less 10s (t<10). can recover using nyquist theorem? if not , recover it? edit: have taken fourier transform of signal , : $$x(ω)=2i(\frac{1}{iω}+πδ(ω))sin(5ω)$$ can lead finding period $$\frac{2π}{5} $$ , see if f>= 5/π can recovered. may not possible because used theorem although on finite signal no need think "finite length". though continuous time signals defined infinite time interval, in practice analyse in finite interval only. x(t) defined in interval [-5 5]. the frequency domain representation of such signal infinite bandwidth sinc function. hence not possible define particular sample rate per nyquist theorem, reconstruct without losing information. can sample definite sample rate, implicitly band limits signal. sampled signal after reconstruction through dac , lpf, not pe...
Read more

sqlite - Unique combination of values - Database Administrators Stack Exchange

i want create database program. use sqlite, although others option. i have columns a , b , c , d . a unique , primary key. b , c , d allowed contain duplicate value. however, don't want combinations of b , c , d repeat. instance, sample valid db: a b c d 0 18 n kiwi 1 12 v kiwi 2 15 t orange 3 12 j kiwi 4 12 t banana 5 31 f apple 6 10 h kiwi 7 15 y orange 8 20 b apple 9 1 m grapefruit 10 7 s apple 11 4 h banana 12 31 t egg sample invalid db (rows 2 , 7 ): a b c d 0 18 n kiwi 1 12 v kiwi 2 15 y orange 3 12 j kiwi 4 12 t banana 5 31 f apple 6 10 h kiwi 7 15 y orange 8 20 b apple 9 1 m grapefruit 10 7 s apple 11 4 h banana 12 31 t egg is there standard database rule or concept applies this? i can of course validation in code, manually querying db. believe construct fifth bcd column, concatenates other three, , required un...
Read more

auto reset an Arduino using ftdi - DTR signal stays low and needs to go high after 1-50ms - Electrical Engineering Stack Exchange

Image
hello have cheap ftdi going recreate on pcb can flash atmega2560 chip onboard, ftdi has dtr line pulled low when sequence starts stays low instead of going low high after 1ms 50ms, need find out how create simple circuit when pulled low goes high, how can this, have simple components hand. my stocked parts: 103 ceramic caps 25uf aluminium caps 220uf aluminium caps some blue ceramic caps labeled "10" practically common resistors values 5v zener diodes 5v switching diodes npn transistors n channel mosfets 5v reflecting diodes can make using ? else can what's needed. many thank edwin sorry it's atmel atmega 2560 chip on pcb have serial lines , reset,5v,ground , 2 gpios on pin out. can flash ftdi. , ftdi dtr line stay low , need pluse rest line need figure out how use low signal pull reset low high right after. if try on arduino mega or uno holding down reset not work it's pulse going low high load boot manager. hence dfti dtr...
Read more